Howdy peoples how are we all? Great now lets start, today im getting of my arse and sprucing up my interior lights.......again. I purchased el dails on ebay when i first got my car back in "07" i think it was and my jeebuz was it cheap compared to today. Guess how much i paid?........wrongzzzzzzzzz only $70 dollars or around there from memory. These days its hard to even buy a set of el dails for cheaper than $200 and if you do hook a brother up. Anyways I will also give a rough guide how to change the lights on the hazzard and de-fog light switches aswell.
First of we start with a car, in my case the 200sx is our lady for today. We'll start of by removing the cluster trim and then the cluster itself. In my case i had to remove the top shroud of the steering column for easier removal of the cluster trim.
Yes i know i know dirty dash ahh well gives me a chance to clean it while we have it out. As you see here there are two screws up top of the cluster trim and two clips which hold it on the bottom. Also the top steering shroud can be removed by just removing the 4 outter screws on the bottom.
Here we can see the cluster trim and top steering shroud removed. There are 3 screws which hold the cluster in place so just remove them and pull the cluster forward to access the plugs behind. Carefully trying not to damage the printed circuit board on the back of the cluster, remove the connectors on the back.
With a flat blade screw driver carefully push back the black tabs on the cluster to remove the front clear cover and bottom plastic cover together.
Here is the cluster with the front cover removed. I will start with the fuel gauge first then speedo, the same steps can be applied to the temperature and tacho gauges.
On the fuel and temperature gauges there is 1 screw holding the black dials on. simply remove the screw and then apply the EL DAILS on top.
Apply the El Dail on by feeding the needle through the hole then align the locators on the dial and simply screw in place. In the photo you can see how i routed the wire up the top. If you remove the 3 main bulbs that light up the cluster at the back you can then use the holes to feed the wiring through.
Here you can see the wire from the fuel dial we just installed protruding from the hole where the original globe used to be.
With the speedo dial remove two small screws near the needle and then you can slip the dial on the extremely long knob. Carefully push the needle to about 3 o'clock and slide the needle through the dial. Doing it any other way will break or cause the needle to dismount from the gauge. Once the needle has slid through position the dial to lign up with the needle pin and then screw the dial in place. With the speedo and tacho i decided to use the middle globe hole to route the wiring through.
Repeat the process with the tacho and temp gauges. As you can see with the tacho and speedo dials its abit trickier so i removed the gauges out of the cluster just to make it that bit easier but it can also be done with the gauges still bolted in.
Heres the cluster with all dials fitted and the cover refitted.
Here you can see the dial wires coming out the back of the cluster where the globes used to be.
Here we have the plug for the dimmer switch. Find your power and earh wires and use them to power the control module for the el dails. I found red with blue trace was my power and black was earth. On the control box for the el dails the power wire is red and earth is black, idiot proof really.
I choose to solder for better contact but if you want to be cheap or dont have access to a soldering iron then scotch locks are ok i guess or if you want to be a real cheap dodgy kent then just splice rap and tape the wires together. Unfortunatly i dont have pics of the control module but you'll work it out. Connet the dial wires to the wires on the module then mount the module and tidy up your wiring. I like to use cable ties to route and mount my wiring to keep things neat. Being an auto technician i hate seeing dodgy wiring jobs and then having to fix em up. So take your time and don't be a dodgy kent. Ok now its time to refit the cluster, simply reverse to removal so im not going to type this stuff out again.
Here we have our cluster refited along with appropriate trims. If you take notice on the bottom left hand of the picture you can see the control switch. This switch is connected to the el dial control module so route the wire so you can mount it in place. I chose to mount next to the factory dimmer switch. With el dails you can order specific colours to suit your taste and they usually come in two colours!!!!! With the kit i purchased i got blue and a greeny type colour. With the switch you can control brightness and colour, ohh and the switch lights up aswell.
Ahhhh beautiful....just beautiful. How much nicer do these dials look a night?. Not only do our dials lok good at night they also look schmick in day light. I can't complain can you?
Have you ever tried to turn your hazards or dimmer switch on at night and went to reach for it but couldn't find the button? Thats because the globes has blown dood.
These are the culprits that are causing me trouble at night. On the s14 the switches are on the aircon control facia. Simple to remove just yank it out, its only clipped in.
Now we have the switches removed we want to pull the button covers of and then pull the tiny little friggin globes out and check for power. We do so plugging the switches back in and turning your parker lights on after we've removed the button covers. Find your power pin and remember it, this is important because we are using LED lights to replace the globes. LED lights are diode so the only work one way.
Here we have our switch with the button cover removed. If you look closely you can see the tiny pins. I found the bottom pin on both switches were my power wires.
Here is a picture of the LED lights im using. Led lights can be purchased online or at your local tech store ie. dick smiths? Make sure it is a 12v LED as your power source in your car used 12v. I opted to use blue because its a sick colour, well red is my favourite colour but blue looks good for this aplication. As you can see i chopped the wires down to fit in the switch. After you cut to appropriate size strip the wire and tint it with solder to make it easy to solder onto the pin on the switch. You also want to tin the pin aswell. Now most important is to solder, there is no other way to do this you must solder so stop being gay and go buy a quality soldering iron and solder and electrical tape.
Now there is virtually little room to solder here so steady hands and skill is needed. If you have never soldered before practice on the left over wire you chopped off. It is important to use a hot soldering iron so let it warm up atleast 5 minutes before use. I used a 25w soldering iron which is sufficient for this type of stuff but im sure 60w or 75w irons are ok but could get nasty. Make sure you use a small soldering tip aswell guys.
In the photo you can see the LED soldered in place. You might find you have to cut the LED wires abit long because of the risitor in the wiring. Not a problem as you can bend and fold it into place.
Now we can fit the button covers back on and mount the switches back in the facia.
Heres a shot of my switches at night. As you can see with LEDs they dont emit light on a wide range. You can purchase wide light emiting LEDs but meh im happy with this. The hazzard button is abit gay also but thats because of the button cover, it really doesnt let alot of light through. If your clever you can see i did my security light too, pretty ey?
Have fun with this one guys and be creative. It takes time and comitment to make your car look nice so appreciate what you are doing and the results will reward you.





















No comments:
Post a Comment